油藏中后期减氧空气驱提高采收率机理研究

尕斯库勒油田E¹₃油藏已经进入高含水时期，储采失衡加剧，综合含水率达到了80%以上，原油产量下降，经济效益变差。为了提高油藏原油采出程度、改善油藏开发效果，调研了国内外减氧空气驱的机理研究以及现场试验的资料，建立了以油藏真实孔渗饱数据为基础的一维条形地层机理模型，并选取该油藏Y12-27井组进行了减氧空气驱可行性验证。研究表明:纵向顶部减氧空气驱驱油效果优于水驱和氮气驱；驱替压力对原油采出程度影响不大；注水转注气可以提高原油采出程度；对于减氧空气驱，由于低温氧化反应的作用，氧气浓度对原油采出程度有一定影响，但比较微弱，其中，氧气浓度为10%时，驱替结束采出程度最高；尕斯库勒油田E¹₃油藏属于注水开发“双高”油藏，适用于减氧空气驱；对于该油藏Y12-27井组，顶部减氧空气驱驱油效果好于水驱和氮气驱，建议氧气浓度超过10%时采取关井等措施。     

汽车安全带固定点失效分析及结构优化

以乘用车后排安全带固定点为对象，基于安全带固定点强度试验结果，通过有限元方法建立模型，简化并调试有限元模型，进行试验对标分析。经过对标后，有限元分析结果与试验结果基本吻合。然后基于对标后的有限元模型对结构进行优化，提高安全带固定点强度，提出优化方案，并通过试验验证，满足法规要求。通过利用CAE分析技术在产品开发过程中的应用，有效找到问题原因并有针对性地加以优化，从而缩短开发周期和节约成本。     

Continuous Flow Fabrication of Block Copolymer–Grafted Silica Micro‐Particles in Environmentally Friendly Water/Ethanol Media

Polymer‐grafted inorganic particles (PGIPs) are attractive building blocks for numerous chemical and material applications. Surface‐initiated controlled radical polymerization (SI‐CRP) is the most feasible method to fabricate PGIPs. However, a conventional in‐batch reaction still suffers from several disadvantages, including time‐consuming purification processes, low grafting efficiency, and possible gelation problems. Herein, a facile method is demonstrated to synthesize block copolymer–grafted inorganic particles, that is, poly(poly(ethylene glycol) methyl ether methacrylate) (PPEGMEMA)‐b‐poly(N‐isopropylacrylamide) (PNIPAM)–grafted silica micro‐particles using continuous flow chemistry in an environmentally friendly aqueous media. Immobilizing the chain transfer agent and subsequent SI‐CRP can be accomplished sequentially in a continuous flow system, avoiding multi‐step purification processes in between. The chain length (MW) of the grafted polymers is tunable by adjusting the flow time or monomer concentration, and the narrower molar mass dispersity (Р< 1.4) of the grafted polymers reveals the uniform polymer chains on the particles. Moreover, compared with the in‐batch reaction at the same condition, the continuous system also suppresses possible gelation problems.     

Passive micromixer with baffles distributed on both sides of microchannels based on the Koch fractal principle

Since the beginning of the 21st Century, the development of microfluidic chip technology has been very rapid and has attracted the attention of more and more scholars. As an important part of the microfluidic chip, the performance of the micromixer is critical. The fractal structure in the microchannels helps to improve the mixing performance of the micromixer and improve the mixing efficiency of the micromixer. The research results of other scholars are of great significance to the research of the present paper, which mainly studies the effect of changing the baffle state on the mixing efficiency of the micromixer based on the Koch fractal principle. Through simulation analysis, it was found that the mixing efficiency of the baffles distributed on both sides of the microchannel was higher than the mixing efficiency of the baffles distributed on the microchannel side. When the distance between adjacent baffles was divided into 0.15, 0.25 and 0.35 mm, simulated data suggested that the baffle distance of 0.15 mm was best. Increasing the number of baffles from six to eight groups increased the mixing path of the fluid in the microchannel and improved mixing efficiency. A comparison of mixing efficiencies of the 0°, 15° and 30° baffle angles revealed that very significant improvement in mixing efficiency was obtained at 30°. © 2019 Society of Chemical Industry     

负载羧基化球状介孔纳米颗粒TFN膜的研究

在薄层复合膜(thin-film composite membrane, TFC膜)中引入无机纳米颗粒，形成薄层纳米复合膜(thin-film nanocomposite membrane, TFN膜)，近几年作为反渗透膜开始应用于水处理研究。但是无机纳米颗粒在TFC膜中的性能的不稳定性和膜的机械强度等变成了突出问题。合成制备了粒径约为110 nm修饰羧基的介孔氧化硅球状纳米颗粒(MSN—COOH)，并将其成功地化学键合在TFC膜的表面功能层交联网络中。与TFC膜相比，键合有MSN—COOH的TFN膜，水通量提高了56.2%，保持高脱盐率；由于单分散介孔纳米颗粒表面亲水官能团的引入，使膜表面的亲水性有很大程度提高，单分散介孔纳米颗粒在基体中的有序排列，使膜表面粗糙度降低，提高了膜的抗污染能力。与普通TFN膜相比较，具有更好的稳定性和柔韧性，可以在长时间高压过滤操作下保持稳定。     

喷油方式对斜齿轮齿面温度的影响

为探讨喷油方式对齿面温度的影响，以斜齿轮为研究对象，通过CFD仿真和试验研究不同喷油方式对斜齿轮齿面温度的影响。针对斜齿轮喷油润滑过程的特点，分析其齿面摩擦生热量，简化轮齿喷油润滑计算模型，并基于CFX进行齿面对流换热仿真研究，得到了不同喷油方式下的齿面温度；基于功率开放式斜齿轮试验平台，对不同喷油方式下的齿面温度进行了试验测量，与仿真计算结果进行对比分析。结果表明：在高速重载斜齿轮传动系统中，啮出侧喷油润滑的方式比啮入侧喷油润滑方式的冷却降温效果要好。     

长走向平行钒铁矿体协同开采方案研究

七角井矿区的钒、铁双层矿体走向长度超4 km且呈近似平行产出，下盘铁矿开采时损失贫化率高且上盘钒矿资源保护难度大。根据钒铁矿体走向长、近平行产出、厚度负相关、空区隐患大的开采技术条件 特征，采用平面分区、开采时序规划、采矿方法优化、区域稳定性控制等技术来实现钒铁矿协同开采。根据铁矿“中间厚、两端薄”、钒矿“中间薄、两端厚”的形态特征，将长走向的钒铁矿体分为东区、中区及西 区。工程空间上，双层矿体共用一套开拓、采准、运输等开采系统；开采时序上，在提高铁矿生产能力的同时保证了钒矿开采的时间灵活性；采矿方法上，东区及西区铁矿采用阶段矿房嗣后膏体微胶结充填法，中区 铁矿采用阶段矿房法转崩落法；此外，通过中区崩落顶板及上盘围岩，东、西区膏体充填方式保证了矿区开采时及开采后的区域稳定性。研究表明：所提出的协同开采方案使矿山铁矿设计开采储量增加了1 064.7万t ，膏体充填每年消耗干抛层、尾矿等矿山固废86万t以上，矿山安全及经济效益明显。